| 
  • If you are citizen of an European Union member nation, you may not use this service unless you are at least 16 years old.

  • You already know Dokkio is an AI-powered assistant to organize & manage your digital files & messages. Very soon, Dokkio will support Outlook as well as One Drive. Check it out today!

View
 

MP Telescopic Handler

Page history last edited by Michael 5 years, 4 months ago

back to the Index, or to the Vehicles page

 


 

Description

 

this is a "cutaway" view of the basic diesel-powered model

 

      Derived from the diesel-powered JCB 525-4 telescopic handler -- JCB pioneered the telehandler concept in 1977; the 525-4 is from about 1981. About 370 kg of fuel tank, engine and transmission parts were removed; they were replaced with a Mk 1 fusion generator and a 40 kilowatt electric motor. The radiator was retained for high-power operation (i.e., powering other equipment), however the forklift can usually operate without requiring the cooling system.

     It has all-wheel drive and rear-wheel steering. There is a towing eye at the rear, mostly for towing this vehicle, but it can tow military or contractors' trailers -- however, there's not connection for brake lines.

     The cab is fully-enclosed by a roll-over cage, with polycarbonate windows all around. It's got a heater, windshield wiper.

     The lift height with the full rated load is 6.4 meters; the reach is 3.65 meters; the maximum load at full reach is 860 kg.

 

Specifications

 

Crew:  1

Weight:  empty, 6,180 kg; rated load 2,500 kg

Length:  3.6 m over fork face; xx m over wheels

Width:  1.82 m

Height:  2.2 m over cab

Ground clearance:  0.36 m

Turning radius:  inside, 2.22 m; outside, 5.11 m

Ground pressure:  xxx kg/square centimeter

Max speed: 

(highway) 30 kph

(offroad) xx kph

Fording:  xxx m

Gradient:  xx% when fully loaded

Engine:  40 kilowatt electric motor

Electrical system:  12 V; there are two headlamps, two reversing lamps, two side lamps, stop/tail lights, a rotating amber beacon on top of the cab, and a recharging plug for the batteries

Batteries:  four Morrow Project vehicle batteries

 

Maintenance and Installed Equipment

 

     Since the internal combustion engine has been entirely replaced, keeping the vehicle operating is much easier -- but it still needs maintenance. Besides daily checks, an actual inspection is called for by the manual after 100 hours, and a more thorough inspection every 400 hours.

 

  • Cooling:  19.3 liters of water is needed to fill the radiator and cooling system. 

  • Lubrication:  the differentials and wheel hubs need a total of 23.5 liters of lubricating oil. The chassis and crane need some lubricating and greasing every so often.

  • Hydraulics:  275 liters of hydraulic fluid are needed, for the brakes and boom. 

  • Tiresthe tires are 12.5x18 and 15.5x24

 

Accessories

 

     There are several options and accessories:  an extension jib and crane hook (giving a maximum lift height of 7.9 meters); a simple steel dump bucket (for rubble or gravel handling, not really able to cut into dirt very well); a 2.4 meter wide aerial work basket ("personnel platform"); and various fork and mast variations (including a lifting mast). With a lifting mast at the end of the boom, maximum capacity is reduced to 1500 kg, but of course the operator has more flexibility in placing and raising the load.

     A military tow pintle is fitted at the rear, along with power and brake line cables.

 

Variants

 

     The Project tested the vehicle with an array of 100 "vehicle batteries" instead of the fusion generator and radiator ... it could operate at continuous full power for 3.75 hours, or in a more typical 60% "use factor" for 6.25 hours.

Comments (0)

You don't have permission to comment on this page.